STANDARDS & DATASHEETS

Standards & Datasheets — DIN / ANSI / JIS PN10 Plastic Valves

Design institutes and project engineers use this page to compare the three flange standards supported across the RUNKE PN10 valve range, and to request product datasheets. All data below is taken from the official RUNKE catalogue.

1. The Three Standards 2. Rating & Drilling 3. Datasheets (PDF) 4. Application Limits 5. FAQ Choose Your Standard

1. The Three Standards & Their Markets

Standard	Full Name	Pressure Rating	Main Export Markets
DIN	DIN EN 1092-1, PN10 flange drilling	PN10 (10 bar @ 20 °C)	Europe, Middle East, Australia
ANSI	ASME B16.1, Class 125	PN10 equivalent working pressure	North America, South America
JIS	JIS B2210, 10K	10K (≈ PN10 working pressure)	Southeast Asia, Japan, Korea

2. Key Point — One Rating, Three Drillings

⚠️ PN10 pressure rating applies for all three standards, but flange hole dimensions are different and not interchangeable. A DIN PN10 valve will not bolt onto an ANSI or JIS flange of the same DN. Always state the standard in your inquiry or purchase order.

2.1 Pressure Rating by Size (official)

Valve series	Pressure rating by size (official)
Lever & gear butterfly valve	PN10 (2"–8") · PN6 (10"–12") · PN4 (14"–16")
Non-actuator (ISO 5211) butterfly	PN8 (2"–6") · PN6 (8") · PN5 (10"–12") · PN4 (14"–16")
True-union ball valve	PN16 (1/2"–2") · PN10 (2-1/2"–4")
Check / foot valve series	PN10 (up to 6") · PN6 (8" and above, wafer series)

2.2 Flange Comparison — Official Drilling Data (butterfly valve series)

Size	Body Ø D (mm)	DIN / GB		ANSI Class 125		JIS 10K
Size	Body Ø D (mm)	PCD mm	Holes n-Øe	PCD mm	Holes n-Øe	PCD mm	Holes n-Øe
DN50 / 2"	165	125	4-Ø20	120.5	4-Ø20	120	4-Ø20
DN65 / 2-1/2"	184	145	4-Ø20	139.5	4-Ø20	140	4-Ø20
DN80 / 3"	200	160	8-Ø20	152.5	4-Ø20	150	8-Ø20
DN100 / 4"	229	180	8-Ø20	190.5	8-Ø20	175	8-Ø20
DN125 / 5"	262	210	8-Ø20	216	8-Ø26	210	8-Ø26
DN150 / 6"	290	240	8-Ø26	241.5	8-Ø26	240	8-Ø26
DN200 / 8"	350	295	8-Ø26	298.5	8-Ø26	290	12-Ø26

Source: RUNKE official catalogue (butterfly valve series). PCD = pitch circle diameter; n-Øe = number of holes × hole diameter. Ball valves and socket-end valves use socket standards (DIN / ANSI / JIS / BS) instead of flanges — ask us for the socket-dimension table.

⚠ Data from the official catalogue — still verify against the approved drawing before fabrication or ordering.

3. Product Datasheets (PDF)

Click a product name to open its page, or Request → for the PDF datasheet (dimensions per standard, material list, torque data). We send it within 24 working hours (GMT+8).

Butterfly Valves5

PVC-U Butterfly Valve (Lever)PDFRequest →

PVC-U Butterfly Valve (Gear)PDFRequest →

PVC-U Butterfly Valve (Actuator-Ready)PDFRequest →

PVC-U Flange Butterfly Valve PDFRequest →

FRPP / PPR Butterfly Valve PDFRequest →

Ball Valves4

PVC-U True Union Ball Valve A PDFRequest →

PVC-U True Union Ball Valve B PDFRequest →

PVC-U Non-Actuator Union Ball Valve PDFRequest →

PVC-U Two-Piece Compact Ball Valve PDFRequest →

Check Valves4

PVC-U Wafer Check Valve PDFRequest →

PVC-U Wafer Flange Check Valve PDFRequest →

PVC-U Swing Check Valve PDFRequest →

PVC-U Flanged Swing Check Valve PDFRequest →

Foot Valves4

PVC-U Swing Foot Valve PDFRequest →

PVC-U Flanged Swing Foot Valve PDFRequest →

PVC-U Union Foot Valve PDFRequest →

PVC-U Flanged Union Foot Valve PDFRequest →

Actuators1

Pneumatic Actuator (Quarter-Turn)PDFRequest →

Need the complete catalogue, socket-dimension tables or pneumatic-actuator torque data? Request the full catalogue →

4. Application Limits (per manufacturer catalogue)

Approved duty: clean water service at PN10 (10 bar @ 20 °C). The rating changes with size — check the table in section 2.1 before selecting.

✕Not suitable for

✕Chemical process lines — Water service only. For aggressive media, request CPVC / FRPP / PPR bodies and a chemical-compatibility check.
✕Gas or multiphase media — Not for gas, gas-liquid or solid-liquid multiphase service — the range is designed for liquid water duty.
✕Vacuum duty — Not suitable for vacuum. Drain the valve and the pipeline to prevent freezing during shutdown.
✕Mixing standards on one line — A DIN PN10 valve will not bolt onto an ANSI or JIS flange of the same DN.

✓Required for correct installation

✓Wafer check valve clearance — Install at least 5 × DN from the pump outlet, and follow the flow arrow only.
✓Horizontal check valves — Keep the lifting ring facing upward so the disc seats correctly.
✓State the standard on the PO — DIN / ANSI / JIS drilling must be confirmed on the inquiry and the purchase order.
✓Verify before fabrication — Catalogue drilling data is for reference — confirm against the approved drawing before ordering.

5. Frequently Asked Questions

Quick answers to the questions engineers ask most often about standards, drilling and supply:

Do your valves support DIN, ANSI and JIS with a PN10 rating?

Yes. The whole PN10 range is supplied in all three drillings: DIN EN 1092-1 PN10, ASME B16.1 Class 125 (ANSI) and JIS B2210 10K. The pressure rating is PN10 for all three — only the flange drilling differs (pitch circle diameter, number of holes and hole diameter), and the drillings are not interchangeable. Always state the required standard on your inquiry and purchase order. Full comparison in section 2.2.

Can you make custom flange drilling?

Yes. We adjust materials, specifications, sealing forms and connection modes (flange, socket, thread) to your drawings, samples or actual working conditions, including non-standard flange drilling. OEM / ODM is supported — custom logo, packaging and private mould development. Lead time: 7–15 working days for customisation on existing moulds, 15–25 working days where a new mould is required.

What is the temperature limit for PN10 PVC-U valves?

PN10 is rated at 10 bar at 20 °C for water service. Working pressure falls as the service temperature rises, so for duty above ambient temperature — or for media other than clean water — ask us for the derating curve. Body materials available in this range include PVC-U, CPVC, FRPP and PPR, and the catalogue scope is water service only (see section 4).

What is your MOQ & lead-time for project orders?

In-stock items: 3–7 working days after deposit. Mass production of standard products: 10–15 working days. Customised products follow the confirmed cycle — 7–15 working days on existing moulds, 15–25 working days for new moulds. MOQ is flexible and small orders are acceptable for conventional products; project orders receive a dedicated quotation and schedule.

Can you provide pressure-test reports?

Yes. Every valve is 100% inspected for sealing, pressure resistance and appearance before it leaves the factory, and production runs under our ISO 9001 quality management system. Qualified product inspection reports are provided with each batch, and third-party inspection can be arranged on request.

Which countries & regions have you exported to?

Our products are sold in more than 30 countries and regions, covering North America, South America, Western and Eastern Europe, Southeast Asia, South Asia, the Middle East and Africa. As a rule DIN drilling is chosen for Europe / Middle East / Australia, ANSI for the Americas and JIS for Southeast Asia, Japan and Korea — see section 1.

View all 17 FAQs →

Choose Your Standard

View DIN PN10 → View ANSI PN10 → View JIS PN10 →

WA @RFQ